| 1. |
- Diaz de Zerio Mendaza, Amaia, 1986, et al.
(författare)
-
Neat C60:C70 buckminsterfullerene mixtures enhance polymer solar cell performance
- 2014
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 2:35, s. 14354-14359
-
Tidskriftsartikel (refereegranskat)abstract
- We demonstrate that bulk-heterojunction blends based on neat, unsubstituted buckminsterfullerenes (C60, C70) and a thiophene–quinoxaline copolymer (TQ1) can be readily processed from solution. Atomic force and transmission electron microscopy as well as photoluminescence spectroscopy reveal that thin films with a fine-grained nanostructure can be spin-coated, which display a good photovoltaic performance. Replacement of substituted fullerenes with C60 or C70 only results in a small drop in open-circuit voltage from 0.9 V to about 0.8 V. Thus, a power conversion efficiency of up to 2.9% can be maintained if C70 is used as the acceptor material. Further improvement in photovoltaic performance to 3.6% is achieved, accompanied by a high internal quantum efficiency of 75%, if a 1 : 1 C60:C70 mixture is used as the acceptor material, due to its improved solubility in ortho-dichlorobenzene.
|
|
| 2. |
- Henriksson, Patrik, 1983, et al.
(författare)
-
Stability study of quinoxaline and pyrido pyrazine based co-polymers for solar cell applications
- 2014
-
Ingår i: Solar Energy Materials and Solar Cells. - : Elsevier BV. - 0927-0248 .- 1879-3398. ; 130, s. 138-143
-
Tidskriftsartikel (refereegranskat)abstract
- We present two co-polymer families; one based on a thiophene-quinoxaline unit and one on a thiophene-pyrido pyrazine unit. Co-polymerization of these monomers with thiophene-hexylthiophene was performed to create polymers with an optical absorption that fully covers the visible part of the solar spectrum with the aim to enhance the solar cell performances of these polymers. We have also studied how increasing the fraction of thiophene-hexylthiophene affects the photo-oxidative stability of these polymers. Thiophene-pyrido pyrazine solar cells displayed increased device efficiency upon addition of the thiophene-hexylthiophene and, in addition, the stability is retained upon inclusion of these units. In contrast, we found that for the thiophene-quinoxaline based co-polymer, both device efficiency and stability decreased with increasing thiophene-hexylthiophene fraction. Moreover, our results indicate that the photo-oxidative stability of the thiophene-quinoxaline co-polymer is independent of the polymer molecular weight as well as of the film thickness.
|
|
| 3. |
- Kroon, Renee, 1982, et al.
(författare)
-
A New Tetracyclic Lactam Building Block for Thick, Broad-Bandgap Photovoltaics
- 2014
-
Ingår i: Journal of the American Chemical Society. - : American Chemical Society. - 0002-7863 .- 1520-5126. ; 136:33, s. 11578-11581
-
Tidskriftsartikel (refereegranskat)abstract
- A new tetracyclic lactam building block for polymer semiconductors is reported that was designed to combine the many favorable properties that larger fused and/or amide-containing building blocks can induce, including improved solid-state packing, high charge carrier mobility, and improved charge separation. Copolymerization with thiophene resulted in a semicrystalline conjugated polymer, PTNT, with a broad bandgap of 2.2 eV. Grazing incidence wide-angle X-ray scattering of PTNT thin films revealed a strong tendency for face-on pi-stacking of the polymer backbone, which was retained in PTNT:firllerene blends. Corresponding solar cells featured a high open-circuit voltage of 0.9 V, a fill factor around 0.6, and a power conversion efficiency as high as 596 for greater than200 nm thick active layers, regardless of variations in blend stoichiometry and nanostructure. Moreover, efficiencies of greater than4% could be retained when thick active layers of similar to 400 rim were employed. Overall, these values are the highest reported for a conjugated polymer with such a broad bandgap and are unprecedented in materials for tandem and particularly ternary blend photovoltaics. Hence, the newly developed tetracyclic lactam unit has significant potential as a conjugated building block in future organic electronic materials.
|
|
| 4. |
- Kroon, Renee, 1982, et al.
(författare)
-
Comparison of selenophene and thienothiophene incorporation into pentacyclic lactam-based conjugated polymers for organic solar cells
- 2015
-
Ingår i: Polymer Chemistry. - : Royal Society of Chemistry (RSC). - 1759-9954 .- 1759-9962. ; 6:42, s. 7402-7409
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, we compare the effect of incorporating selenophene versus thienothiophene spacers into pentacyclic lactam-based conjugated polymers for organic solar cells. The two cyclic lactam-based copolymers were obtained via a new synthetic method for the lactam moiety. Selenophene incorporation results in a broader and red-shifted optical absorption while retaining a deep highest occupied molecular orbital level, whereas thienothienophene incorporation results in a blue-shifted optical absorption. Additionally, grazing-incidence wide angle X-ray scattering data indicates edge- and face-on solid state order for the selenophene-based polymer as compared to the thienothiophene-based polymer, which orders predominantly edge-on with respect to the substrate. In polymer : PC71BM bulk heterojunction solar cells both materials show a similar open-circuit voltage of similar to 0.80-0.84 V, however the selenophene-based polymer displays a higher fill factor of similar to 0.70 vs. similar to 0.65. This is due to the partial face-on backbone orientation of the selenophene-based polymer, leading to a higher hole mobility, as confirmed by single-carrier diode measurements, and a concomitantly higher fill factor. Combined with improved spectral coverage of the selenophene-based polymer, as confirmed by quantum efficiency experiments, it offers a larger short-circuit current density of similar to 12 mA cm(-2). Despite the relatively low molecular weight of both materials, a very robust power conversion efficiency similar to 7% is achieved for the selenophene-based polymer, while the thienothiophene-based polymer demonstrates only a moderate maximum PCE of similar to 5.5%. Hence, the favorable effects of selenophene incorporation on the photovoltaic performance of pentacyclic lactam-based conjugated polymers are clearly demonstrated.
|
|
| 5. |
- Lindqvist, Camilla, 1985, et al.
(författare)
-
Fullerene Nucleating Agents: A Route Towards Thermally Stable Photovoltaic Blends
- 2014
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6840 .- 1614-6832. ; 4:9, s. 1301437-
-
Tidskriftsartikel (refereegranskat)abstract
- The bulk-heterojunction nanostructure of non-crystalline polymer: fullerene blends has the tendency to rapidly coarsen when heated above its glass transition temperature, which represents an important degradation mechanism. We demonstrate that fullerene nucleating agents can be used to thermally arrest the nanostructure of photovoltaic blends that comprise a non-crystalline thiophene-quinoxaline copolymer and the widely used fullerene derivative [6,6]-phenyl-C-61-butyric acid methyl ester (PCBM). To this end, C-60 fullerene is employed to efficiently nucleate PCBM crystallization. Sub-micrometer-sized fullerene crystals are formed when as little as 2 wt% C-60 with respect to PCBM is added to the blend. These reach an average size of only 200 nanometers upon introduction of more than 8 wt% C-60. Solar cells based on C-60-nucleated blends indicate significantly improved thermal stability of the bulk-heterojunction nanostructure even after annealing at an elevated temperature of 130 degrees C, which lies above the glass transition temperature of the blend. Moreover, we find that various other compounds, including C-70 fullerene, single-walled carbon nanotubes, and sodium benzoate, as well as a number of commercial nucleating agents-commonly used to clarify isotactic polypropylene-permit to control crystallization of the fullerene phase.
|
|
| 6. |
- Tang, Zheng, et al.
(författare)
-
Interlayer for Modified Cathode in Highly Efficient Inverted ITO-Free Organic Solar Cells
- 2012
-
Ingår i: Advanced Materials. - : Wiley. - 0935-9648 .- 1521-4095. ; 24:4, s. 554-
-
Tidskriftsartikel (refereegranskat)abstract
- Inverted polymer solar cells with a bottom metal cathode modified by a conjugated polymer interlayer show considerable improvement of photocurrent and fill factor, which is due to hole blocking at the interlayer, and a modified surface energy which affects the nanostructure in the TQ1/[70]PCBM blend.
|
|
| 7. |
- Tang, Zheng, et al.
(författare)
-
Relating open-circuit voltage losses to the active layer morphology and contact selectivity in organic solar cells
- 2018
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 6:26, s. 12574-12581
-
Tidskriftsartikel (refereegranskat)abstract
- We demonstrate that voltage losses due to both radiative and non-radiative recombination of charge carriers are strongly dependent on D/A phase separation. By processing the active layer with various solvent additives, we create distinct morphologies that lead to significantly different device open-circuit voltages (VOC), even though the charge transfer state energy (ECT) of the D/A blend remains rather constant. We find that radiative recombination losses are significantly increased for a finely intermixed morphology, due to the large D/A interface area. This leads to a total recombination loss of ECT - qVOC ≈ 0.7 eV. However, considerably smaller losses (0.5 eV), due to suppressed non-radiative recombination, are possible in solar cells where the D/A materials are organized to only allow for selective charge carrier extraction. Using a drift diffusion model, we show that the origin of the reduced non-radiative recombination losses is related to an effect which has not been considered for 'optimized' solar cells-the suppression of minority carrier diffusion to the 'wrong' contact. Our results suggest that the built-in field is not sufficiently strong even in 'optimized' organic solar cells and that selective carrier extraction is critical for further improvements in VOC.
|
|
| 8. |
- Xia, Yuxin, et al.
(författare)
-
Inverted all-polymer solar cells based on a quinoxaline-thiophene/naphthalene-diimide polymer blend improved by annealing
- 2016
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 4:10, s. 3835-3843
-
Tidskriftsartikel (refereegranskat)abstract
- We have investigated the effect of thermal annealing on the photovoltaic parameters of all-polymer solar cells based on a quinoxaline-thiophene donor polymer (TQ1) and a naphthalene diimide acceptor polymer (N2200). The annealed devices show a doubled power conversion efficiency compared to nonannealed devices, due to the higher short-circuit current (J(sc)) and fill factor (FF), but with a lower open circuit voltage (V-oc). On the basis of the morphology-mobility examination by several scanning force microscopy techniques, and by grazing-incidence wide-angle X-ray scattering, we conclude that better charge transport is achieved by higher order and better interconnected networks of the bulk heterojunction in the annealed active layers. The annealing improves charge transport and extends the conjugation length of the polymers, which do help in charge generation and meanwhile reduce recombination. Photoluminescence, electroluminescence, and light intensity dependence measurements reveal how this morphological change affects charge generation and recombination. As a result, the J(sc) and FF are significantly improved. However, the smaller band gap and the higher HOMO level of TQ1 upon annealing causes a lower V-oc. The blend of an amorphous polymer TQ1, and a semi-crystalline polymer N2200, can thus be modified by thermal annealing to double the power conversion efficiency.
|
|
| 9. |
|
|
